Bosch makes a wide range of built-in ovens, from simple fan-forced models to pyrolytic, steam and compact ovens that stack in a wall tower. We do the electrical side: the right supply, isolation and a tested connection.
Ring 0421 772 661 for a written quote. The model number and a photo of your switchboard and the oven cavity help us quote accurately.
Bosch is a German appliance brand and one of the most common names in Australian kitchens. Its ovens are sold in tiers (Series 2 up to Series 8), and as you move up the range you tend to get more features, such as pyrolytic self-cleaning, added steam, or a compact oven or combination microwave designed to sit above a full-size oven.
Those features change the electrical job. A basic 60cm single oven may arrive with a plug and be happy on a standard power outlet, while a pyrolytic or double-stacked arrangement can draw considerably more and is usually meant to be hard-wired on its own circuit. The rating plate and installation manual are the only reliable guide, so we read them before we quote.
Blue Link Electrical is a licensed electrician based in Hurlstone Park (NSW Contractor Licence 332956C). We connect Bosch ovens you've bought yourself across the Inner West and Sydney. We don't sell Bosch appliances and we aren't a Bosch service agent; faults inside the oven go to the manufacturer's service network.
Most Bosch ovens are 60cm built-in units that go either under the bench below a cooktop or up in a tall wall cabinet. A wall tower is popular because it saves bending, and it often pairs a full-size oven with a compact oven, steam oven or combination microwave above it. Each of those appliances has its own supply requirement, so a tower can mean two separate connections rather than one.
Before you order, check the electrical connection section of the installation manual: whether it's supplied with a plug or expects to be hard-wired, the current rating, and where the supply should come into the cabinet. Cabinetmakers need the ventilation and cut-out dimensions; we need to know where to leave the connection point so it isn't trapped behind the appliance.
A plug-in oven needs a suitable outlet; a hard-wired one needs a dedicated circuit with cable and breaker sized to the rating plate and the length of the run.
A compact oven or microwave above the main oven is a second load. We plan both supplies at once so the cabinet only gets opened up one time.
You need a way to switch the oven off without pulling it out, usually an isolating switch in an adjacent cupboard or on the wall nearby.
The circuit should be protected by a safety switch. Older kitchens may need one added, ideally as an RCBO; see RCD vs RCBO.
A new dedicated circuit needs space and capacity at the board. Ceramic fuse boards normally need an upgrade first.
1. Read the plate and the board. We check the oven's rating and connection type, then look at the switchboard, the existing circuit and the cable run to the kitchen.
2. Prepare the supply. We install or upgrade the circuit, fit the isolating switch where you can reach it, and leave the connection point where the manual says it should be inside the cavity.
3. Connect and fit. Once the cabinetry is ready, we connect the oven, slide it in without crushing the lead, and secure it to the cabinet as the manual describes.
4. Test and certify. We test insulation, earthing and RCD operation to AS/NZS 3000, run the oven up, and issue a Certificate of Compliance for Electrical Work where new wiring is installed. Our cooktop and oven job in Petersham shows a typical kitchen installation.
A long, very hot cleaning cycle can expose a tired connection or an element fault. We test the circuit first to separate wiring from appliance. See oven tripping the safety switch.
Switches or outlets placed directly behind the oven stop it sitting flush. Moving the isolation to the next cupboard fixes it.
A replacement oven with a higher rating than the old one can overload the existing cable and breaker. We check before connecting, not after.
If power is reaching the oven but it won't heat, it's usually an element, sensor or control fault for Bosch service.
Some can. Many single 60cm ovens are supplied with a plug, but higher-rated models are meant to be hard-wired on a dedicated circuit. The manual and rating plate decide it.
Sometimes, if the circuit is sized for the combined load under the wiring rules. With an induction cooktop they are often better on separate circuits. We work it out from both rating plates.
Usually yes. Each appliance has its own supply requirement, so we plan the two connections together.
Yes. We install and wire the oven you've bought. Product warranty and internal repairs are handled by Bosch's service network.
Yes. Blue Link Electrical holds NSW Electrical Contractor Licence 332956C, is fully insured, and issues a Certificate of Compliance for the work.
NSW Electrical Contractor Licence 332956C · Fully insured · Since 2016 · Based in Hurlstone Park
Excellent electrician Blue Link Electrical was honest, knowledgeable, and took the time to answer my questions The work was completed quickly without rushing and everything works perfectly Will be using them
Very professional and reliable service. Blue Link Electrical were punctual, friendly, and knew exactly what they were doing. The job was completed to a high standard and the place was left clean. Highly recommend to anyone needing electrical work.
Can't fault the service from Blue Link Electrical From first contact to job completion everything was smooth and professional Quality workmanship and great attention to detail. One of the best trades experiences I've had. Make sure you do them slowly
Shown in full, as written on our Google Business Profiles.
Send us a few details and we'll get back to you with a clear, upfront quote.